570130.1200 Black Square Adaptable RetroFit EPDM Rubber, Clips Not Included
These Square Adaptable Pipe Flashings are designed for use for square posts or penetrations through the roof. They can be used as standard pull over type or cut open and used as a Retrofit. Retrofit flashings (also called a split flashing or split boot) are used in applications where you cannot slide the flashing over / down a penetration. The retrofit flashing is split to allow you to wrap around the penetration and form a permanent seal with the help of clips. Clips are not included and need to be purchased separately.
• Manufactured from EPDM Polymer and is Ozone and UV resistant for durability, UV characteristics and the ability to withstand constant temperatures between – 40°C and 115°C.
• The EPDM black version is certified for installation to BAL 12.5 rated roof/wall systems
• The EPDM black version is certified for installation to BAL 12.5 rated roof/wall systems
For applications where the Flashing can be slid down over the top of the Square penetration.
1.Trim rubber boot to suit penetration size, ensure surface is clean and dry before application.
2. Slide down penetration using water as a lubricant, if needed
3. Press the flashing base firmly to conform to the shape of the roof profile, smooth out any creases.
4. Using a pencil or marker, mark a line on the roof around the perimeter of the base of the flashing. Ensure the pencil or marker is compatible with the roof profile material.
5. Lift the flashing up the penetration far enough to allow for application of the sealant.
6. Apply the sealant to the roof profile just inside the marked perimeter line.
7 Slide the flashing to down the penetration to its previous conformed position.
8 Apply pressure to create a seal then fasten using self-drilling screws with EPDM Seals fitted.
Ensure the first screws used are at either side of a crest of the profile starting at the direction from which the water will flow and work your way around from there. Screws should be a maximum of 30~35mm apart.
For applications where the Flashing cannot be slid down over the top of the penetration. (Retro fitting)
1. Trim rubber boot to suit penetration size, then cut the seam of the flashing. Ensure surface is clean and dry before application.
2. With seam in downstream position wrap boot around penetration and engage 1st double
clip at top of seam using multigrips, then, engage remaining clips working down from
top of tuber boot to base.
3. Press the flashing base firmly to conform to the shape of the roof profile, smooth out any creases.
4. Using a pencil or marker, mark a line on the roof around the perimeter of the base of the flashing. Ensure the pencil or marker is compatible with the roof profile material.
5. Lift the flashing up the penetration far enough to allow for application of the sealant.
6. Apply the sealant to the roof profile just inside the marked perimeter line.
7 Slide the flashing to down the penetration to its previous conformed position..
4. Apply pressure to create a seal then fasten using self-drilling screws with EPDM Seals fitted.
Ensure the first screws used are at either side of a crest of the profile starting at the direction from which the water will flow and work your way around from there. Screws should be a maximum of 30~35mm apart.
1.Trim rubber boot to suit penetration size, ensure surface is clean and dry before application.
2. Slide down penetration using water as a lubricant, if needed
3. Press the flashing base firmly to conform to the shape of the roof profile, smooth out any creases.
4. Using a pencil or marker, mark a line on the roof around the perimeter of the base of the flashing. Ensure the pencil or marker is compatible with the roof profile material.
5. Lift the flashing up the penetration far enough to allow for application of the sealant.
6. Apply the sealant to the roof profile just inside the marked perimeter line.
7 Slide the flashing to down the penetration to its previous conformed position.
8 Apply pressure to create a seal then fasten using self-drilling screws with EPDM Seals fitted.
Ensure the first screws used are at either side of a crest of the profile starting at the direction from which the water will flow and work your way around from there. Screws should be a maximum of 30~35mm apart.
For applications where the Flashing cannot be slid down over the top of the penetration. (Retro fitting)
1. Trim rubber boot to suit penetration size, then cut the seam of the flashing. Ensure surface is clean and dry before application.
2. With seam in downstream position wrap boot around penetration and engage 1st double
clip at top of seam using multigrips, then, engage remaining clips working down from
top of tuber boot to base.
3. Press the flashing base firmly to conform to the shape of the roof profile, smooth out any creases.
4. Using a pencil or marker, mark a line on the roof around the perimeter of the base of the flashing. Ensure the pencil or marker is compatible with the roof profile material.
5. Lift the flashing up the penetration far enough to allow for application of the sealant.
6. Apply the sealant to the roof profile just inside the marked perimeter line.
7 Slide the flashing to down the penetration to its previous conformed position..
4. Apply pressure to create a seal then fasten using self-drilling screws with EPDM Seals fitted.
Ensure the first screws used are at either side of a crest of the profile starting at the direction from which the water will flow and work your way around from there. Screws should be a maximum of 30~35mm apart.
| Size | Pack Type | Colour | 480 Y Material | 490 Y Description/Features | 610 Y Base Size | Code |
|---|---|---|---|---|---|---|
| No. 03 |
|
|||||
| No. 05 |
|